Yamaha 2005 YZF-R1T Owner'S Manual Download Page 80

Page: 80 / 106

PERIODIC MAINTENANCE AND MINOR REPAIR

6-31

5. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

CAUTION:

ECA10640

Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.

6. Turn the key to “ON” and turn on

the electrical circuit in question to
check if the device operates.

7. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

1. Fuse box
2. Cowling

1. Headlight fuse
2. Spare fuse

3. Left radiator fan fuse

4. Right radiator fan fuse
5. Backup fuse (for odometer, clock and immo-

bilizer system)

6. Turn signal light fuse

7. Signaling system fuse
8. Ignition fuse

Specified fuses:

Main fuse:

50.0 A

Backup fuse:

10.0 A

Ignition fuse:

15.0 A

Headlight fuse:

25.0 A

Signaling system fuse:

10.0 A

Turn signal light fuse:

10.0 A

Radiator fan fuse:

15.0 A

Electronic fuel injection fuse:

15.0 A

U5VY21E0.book Page 31 Friday, September 10, 2004 9:21 AM

Summary of Contents for 2005 YZF-R1T











































































































Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands

Yamaha 2005 YZF-R1T, Owner'S Manual

Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands