Yamaha 2005 YZF-R1T Owner'S Manual Download Page 84

Page: 84 / 106

PERIODIC MAINTENANCE AND MINOR REPAIR

6-35

EAU24180

Tail/brake light

This model is equipped with an LED
type of tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.

EAU24201

Replacing a turn signal light
bulb

1. Remove the turn signal light lens

by removing the screw.

2. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screw.

CAUTION:

ECA11190

Do not overtighten the screw, other-
wise the lens may break.

EAU24310

Replacing the license plate
light bulb

1. Remove the license plate light unit

by removing the screws.

2. Remove the socket (together with

the bulb) by pulling it out.

1. Screw

2. License plate light unit

1. License plate light bulb

U5VY21E0.book Page 35 Friday, September 10, 2004 9:21 AM

Summary of Contents for 2005 YZF-R1T











































































































Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands

Yamaha 2005 YZF-R1T, Owner'S Manual

Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands