Yamaha 2005 YZF-R1T Owner'S Manual Download Page 73

Page: 73 / 106

PERIODIC MAINTENANCE AND MINOR REPAIR

6-24

3. Tighten the locknuts, then the axle

nut to their specified torques.

EAU23021

Lubricating the drive chain

The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.

CAUTION:

ECA10581

The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.

1. Clean the drive chain with kero-

sene and a small soft brush.

CAUTION:

ECA11120

To prevent damaging the O-rings, do
not clean the drive chain with steam
cleaners, high-pressure washers or
inappropriate solvents.

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive

chain with a special O-ring chain
lubricant.

CAUTION:

ECA11110

Do not use engine oil or any other lu-
bricants for the drive chain, as they
may contain substances that could
damage the O-rings.

Tightening torques:

Locknut:

16 Nm (1.6 m·kgf, 12 ft·lbf)

Axle nut:

150 Nm (15.0 m·kgf, 108 ft·lbf)

U5VY21E0.book Page 24 Friday, September 10, 2004 9:21 AM

Summary of Contents for 2005 YZF-R1T











































































































Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands

Yamaha 2005 YZF-R1T, Owner'S Manual

Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands