Xilinx Zynq-7000 User Manual Download Page 75 | Manualshive

Page: 75 / 678

background image

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

75

UG586 November 30, 2016

Chapter 1:

DDR3 and DDR2 SDRAM Memory Interface Solution

vio_instr_mode_value[3:0]

Input

Valid settings for this signal are:
• 0x1: Command type (read/write) as defined by fixed_instr_i.
• 0x2: Random read/write commands.
• 0xE: Write only at address zero.
• 0xF: Read only at address zero.

vio_bl_mode_value[3:0]

Input

Valid settings for this signal are:
• 0x1: Fixed burst length as defined in the fixed_bl_i inputs.
• 0x2: The user burst length is generated from the internal PRBS

generator. Each burst value defines the number of back-to-back

commands that are generated.

vio_fixed_instr_value Input

Valid settings are:
• 0x0: Write instruction
• 0x1: Read instruction

vio_fixed_bl_value

Input

Valid settings are 1 to 256.

vio_pause_traffic

Input

Pause traffic generation on-the-fly.

vio_data_mask_gen

Input

This mode is only used if the data mode pattern is

address as data

.

If this is enabled, a random memc_wr_mask is generated after the

memory pattern has been filled in memory. The write data byte

lane is jammed with 8'hFF if the corresponding memc_write_mask

is asserted.

cmp_data[DWIDTH – 1:0]

Output

Expected data to be compared with read back data from memory.

cmp_data_valid

Output

Compare data valid signal.

cmp_error

Output

This compare error flag asserts whenever cmp_data is not the same

as the readback data from memory.

error

Output

This signal is asserted when the readback data is not equal to the

expected value.

error_status[n:0]

Output

This signal latches these values when the error signal is asserted:
• [31:0]: Read start address
• [37:32]: Read burst length
• [39:38]: Reserved
• [40]: mcb_cmd_full
• [41]: mcb_wr_full
• [42]: mcb_rd_empty
• [64 + (DWIDTH – 1):64]: expected_cmp_data
• [64 + (2 × DWIDTH – 1):64 + DWIDTH]: read_data

simple_data0[31:0]

Input

User-defined simple data 0 for simple 8 repeat data pattern.

simple_data1[31:0]

Input

User-defined simple data 1 for simple 8 repeat data pattern.

simple_data2[31:0]

Input

User-defined simple data 2 for simple 8 repeat data pattern.

simple_data3[31:0]

Input

User-defined simple data 3 for simple 8 repeat data pattern.

Table 1-13:

Traffic Generator Signal Descriptions

(Cont’d)

Signal

Direction

Description

«
...
73
74
75
76
77
...
»

Summary of Contents for Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Zynq-7000

Biggest Loser AC-1250-BL

Brand: Taylor Pages: 6

Hamilton Beach Food Processor

Brand: Hamilton Beach Pages: 12

Brand: Hamilton Beach Pages: 19

Brand: Hamilton Beach Pages: 23

Smart Chop 72950

Brand: Hamilton Beach Pages: 32

Stack & Snap 70723

Brand: Hamilton Beach Pages: 36

Big Mouth 70580

Brand: Hamilton Beach Pages: 36

MINI BLITZ CHOPPER

Brand: SQ Professional Pages: 8

Brand: AmazonBasics Pages: 2

Brand: Moulinex Pages: 15

Brand: Hamilton Beach Pages: 36

Brand: National Instruments Pages: 20

Brand: MAGIMIX Pages: 52

Brand: XTA Pages: 58

Brand: emerio Pages: 31

Brand: emerio Pages: 34

Brand: Panasonic Pages: 6

Brand: WHITE BROWN Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands