Xilinx Zynq-7000 User Manual Download

Page: 467 / 678

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

467

UG586 November 30, 2016

www.xilinx.com

Chapter 3:

RLDRAM II and RLDRAM 3 Memory Interface Solutions

This generates a file named

flight_time.csv

in the current directory with package trace

delay information for each pin. While applying specific trace-matching guidelines for the

RLDRAM II/RLDRAM 3 interface, this additional package delay term should be considered

for the overall electrical propagation delay. Different die in the same package might have

different delays for the same package pin. If this is expected, the values should be averaged

appropriately. This decreases the maximum possible performance for the target device.

These rules indicate the maximum electrical delays between RLDRAM II/RLDRAM 3 signals:

• RLDRAM II

For x36 data width, the maximum skew between DQ[17:0] and DK/DK#[0] should be

±15 ps.

For x36 data width, the maximum skew between DQ[35:18] and DM and DK/DK#[1]

should be ±15 ps.

For x18 data width, the maximum skew between any DQ/DM and DK/DK# should be

±15 ps.

• RLDRAM 3

The maximum skew between DQ[8:0] and DQ[26:18] and DM[0] to DK/DK#[0]

should be ±15 ps.

The maximum skew between DQ[17:9] and DQ[35:27] and DM[1] to DK/DK#[1]

should be ±15 ps.

• The maximum skew between any DQ and its associated QK/QK# should be:

RLDRAM II: ±15 ps

RLDRAM 3: ±10 ps

• The maximum skew between any address and control signals and the corresponding

CK/CK# should be ±50 ps.

• The maximum skew between any DK/DK# and CK/CK# should be ±25 ps.

Pinout Requirements

Xilinx 7 series FPGAs are designed for very high-performance memory interfaces, and

certain rules must be followed to use the RLDRAM II/RLDRAM 3 physical layer. Xilinx 7

series FPGAs have dedicated logic for each byte group. Four byte groups are available in

each 50-pin bank. Each 50-pin bank consists of two pairs of multiregion clock capable I/O

(MRCC) pins and four byte groups that contain 1 DQS clock-capable I/O pair and 10

associated I/Os.

Send Feedback

Summary of Contents for Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Zynq-7000

Reviews:

Related manuals for Zynq-7000

Brands by name

Popular brands

Xilinx Zynq-7000, User Manual

Search results

Summary of Contents for Zynq-7000

Reviews:

Related manuals for Zynq-7000

Brands by name

Popular brands