Xilinx Zynq-7000 User Manual Download Page 426

Page: 426 / 678

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

426

UG586 November 30, 2016

www.xilinx.com

Chapter 3:

RLDRAM II and RLDRAM 3 Memory Interface Solutions

The core is composed of these elements, as shown in

Figure 3-38

• Client Interface
• Memory  Controller
• Physical  Interface
• Read  Path
• Write  Path

The client interface (also known as the user interface) uses a simple protocol based entirely

on SDR signals to make read and write requests. For more details describing this protocol,

see the

Client Interface

section.

The Memory Controller takes commands from the user interface and adheres to the

protocol requirements of the RLDRAM II/RLDRAM 3 device. For more information, see the

Memory Controller

section.

The physical interface generates the proper timing relationships and DDR signaling to

communicate with the external memory device, while conforming to the

RLDRAM II/RLDRAM 3 protocol and timing requirements. For more details, see the

Physical

Interface

section.

X-Ref Target - Figure 3-38

Figure 3-38:

Components of the RLDRAM II/RLDRAM 3 Memory Interface Solution

Write Path

Read Path

Client Interface

Memory Controller

mc_phy

clk

sys_rst

Infrastructure

rld_phy_top

byte_lane_

mapping

User Interface

rld_ck_p

Physical Interface

RLDRAM II/
RLDRAM 3 Device

User Design

UG586_c3_02_120411

rld_ck_n

rld_cs_n

rld_dk_p

rld_dk_n

rld_we_n

rld_ref_n

rld_a

rld_ba

rld_dq

rld_dm

rld_qk_p

rld_qk_n

rld_qvld

rld_reset_n

user_cmd_en

user_rd_cmd

user_addr

user_ba

user_wr_en

user_wr_data

user_wr_dm

user_afifo_empty

user_afifo_aempty

user_afifo_full

user_afifo_afull

user_wdfifo_empty

user_wdfifo_aempty

user_wdfifo_full

user_wdfifo_afull

user_rd_valid

user_rd_data

init_calib_complete

Send Feedback

Summary of Contents for Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Zynq-7000

Reviews:

Related manuals for Zynq-7000

Brands by name

Popular brands

Xilinx Zynq-7000, User Manual

Search results

Summary of Contents for Zynq-7000

Reviews:

Related manuals for Zynq-7000

Brands by name

Popular brands