Xilinx Zynq-7000 User Manual Download Page 82 | Manualshive

Page: 82 / 678

background image

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

82

UG586 November 30, 2016

Chapter 1:

DDR3 and DDR2 SDRAM Memory Interface Solution

Calibration and other DDR data read and write transactions are similar to what is described

in

Simulating the Example Design (for Designs with the Standard User Interface), page 66

The AXI4 write and read transactions are started only after the

init_calib_complete

signal is asserted.

Setting Up for Simulation

IMPORTANT:

The Xilinx UNISIM library must be mapped into the simulator.

The test bench provided with the example design supports these pre-implementation

simulations:

• The test bench, along with vendor’s memory model used in the example design
• The RTL files of the Memory Controller and the PHY core, created by the MIG tool

The Questa Advanced Simulator, Vivado Simulator, IES, and VCS simulation tools are used

for verification of the MIG IP core at each software release. Script files to run simulations

with IES and VCS simulators are generated in MIG generated output. Simulations using

Questa Advanced Simulator and Vivado simulators can be done through the Vivado Tcl

Console commands or in the Vivado IDE.

IMPORTANT:

Other simulation tools can be used for MIG IP core simulation but are not specifically

verified by Xilinx.

Simulation Flow Using IES and VCS Script Files

To run the simulation, go to this directory:

<project_dir>/<Component_Name>_ex/imports

For a project created with the name set as

project_1

and the Component Name entered

in Vivado IDE as

mig_7series_0

, go to the directory as follows:

project_1/mig_7series_ex/imports

IES and VCS simulation scripts are meant to be executed only in Linux operating systems.

The

ies_run.sh

and

vcs_run.sh

files are the executable files for running simulations

using IES and VCS simulators respectively. Library files should be added to the

ies_run.sh

and

vcs_run.sh

files respectively. See the

readme.txt

file for details

regarding simulations using IES and VCS.

«
...
80
81
82
83
84
...
»

Summary of Contents for Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Zynq-7000

Brand: Scarlett Pages: 8

Brand: BOMANN Pages: 58

Brand: TC Electronic Pages: 61

Brand: Scarlett Pages: 23

Brand: Marani Pages: 39

Sonic Frontiers SFD-1 MK-II

Brand: Sonic Frontiers Pages: 2

Brand: InFocus Pages: 2

Brand: KitchenAid Pages: 32

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 4

Brand: Vivo Pages: 3

Brand: Vivo Pages: 4

Kasanova GIR000096NOC

Brand: Girmi Pages: 36

Brand: Coopers Pages: 2

Micro Food Processor

Brand: Hamilton Beach Pages: 12

Brand: Hamilton Beach Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands