Xilinx ML628 Getting Started Manual Download Page 3

Page: 3 / 52

ML628 IBERT Getting Started Guide

www.xilinx.com

UG806 (v1.0) May 20, 2011

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 1: ML628 IBERT Getting Started Guide

Overview

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Requirements

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setting Up the ML628 Board

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Extracting the Project Files

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Running the GTH IBERT Demonstration

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connecting the GTH Transceivers and Reference Clocks . . . . . . . . . . . . . . . . . . . . . . . . 7

Attach the GTH Quad Connector

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

GTH Transceiver Clock Connections

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

GTH TX/RX Loopback Connections

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Configuring the FPGA  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11
Setting Up the ChipScope Pro Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13
Starting the SuperClock-2 Module  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
Viewing GTH Transceiver Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18

In Case of RX Bit Errors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

DC Blocks

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Closing the IBERT Demonstration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
More Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Running the GTX IBERT Demonstration

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Connecting the GTX Transceivers and Reference Clocks . . . . . . . . . . . . . . . . . . . . . . . 20

Attach the GTX Quad Connector

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

GTX Transceiver Clock Connections

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

GTX TX/RX Loopback Connections

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

SuperClock-2 Frequency Table

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

IBERT Demonstration Designs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Source Directories and Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
IBERT Design Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

example_ibert_v6_q1xx_top.bit

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

example_implement_ibert_v6_q1xx.prj

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

example_implement_ibert_v6_q1xx.xst

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

i2c_sclk2_control.ngc

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

ibert_v6_q1xx.ngc

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

icon_v6_1.ngc

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

vio_v6_si84_so78.ngc

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

implement.bat

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

example_ibert_v6_q1xx.v

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

i2c_sclk2_control_bb.v

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

ibert_v6_qxxx_top.ucf

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Table of Contents

Summary of Contents for ML628





















































Search results

Summary of Contents for ML628

Reviews:

Related manuals for ML628

Brands by name

Popular brands

Xilinx ML628, Getting Started Manual

Search results

Summary of Contents for ML628

Reviews:

Related manuals for ML628

Brands by name

Popular brands