manualshive.com logo in svg

Xerox Versant 2100, User Manual, Page: 65 / 296

Share
Download
Xerox Versant 2100 User Manual Download Page 65

7

Machine Status

Machine Status Overview

Press the Machine Status button on the Control Panel to access the Machine Status
information, including maintenance and reporting features.

• Press configuration information
• Faults
• Billing / Meter information

Machine Information Tab

This tab provides general information about the press such as the currently installed
software version and the press serial number. This area also allows you to print reports
and view details that apply to billing impressions.

Machine Serial Number

The Machine Serial Number is displayed in the General Information area on the Machine
Information tab. Use this number when calling Xerox for technical information or
assistance.

7-1

Xerox

®

Versant

®

2100 Press

User Guide

Summary of Contents for Versant 2100









































































































































































































































































































Reviews:

No comments