Xerox Versant 2100 User Manual Download Page 146

Page: 146 / 296

OHCF (Trays 8 and 9) Specifications

Specification

Item

Short Edge Feed (SEF):

• 8.5 x 11 in. / A4

• 8.5 x 13 in.

• 8.5 x 14 in.

• 10 x 14 in. / B4

• 11 x 17 in. / A3

• 12 x 18 in.

• 12.6 x 17.7 in. / SRA3

• 13 x 18 in.

• 13 x 19 in.
• 12.6 x 19.2 in.

• B5

Long Edge Feed (LEF):

• B5
• 7.25 x 10.5 in. (executive)

• A4

• 8.5 x 11 in.

• 8.0 x 10 in.

Custom sizes: 182-330 mm (7.2-13 in.) Width and 182-488 mm (7.2-19.2
in.) Length

Sheet size

16 lb. to 130 lb. cover / 52-350 gsm

Paper weight

2,000 sheets per tray

Important

When using up to Xerox 24 lb. / 90 gsm paper.

Paper capacity

Loading Media in the Chained OHCF
(Trays 8 and 9)

Refer to

Loading Media in the OHCF (Trays 8 and 9)

for information and step-by-step

instructions.

Xerox

Versant

2100 Press

11-2

User Guide

Chained (Second) Oversized High Capacity Feeder (OHCF / Trays 8 and 9)

Summary of Contents for Versant 2100









































































































































































































































































































Search results

Summary of Contents for Versant 2100

Reviews:

Xerox Versant 2100, User Manual, Page: 146 / 296

Search results

Summary of Contents for Versant 2100

Reviews: