manualshive.com logo in svg

Xerox Versant 2100, User Manual, Page: 130 / 296

Share
Download
Xerox Versant 2100 User Manual Download Page 130

Recommended Solution

Possible Cause

Fault Code

Close the front door of the Finishing
Transport.

Finishing Transport front door
is open

051-300

Power Off / On the press and resend the
print job. If the fault persists, contact the
Customer Support Center.

Finishing Transport firmware
fault upgrade

051-310

Refer to the DFA device user document-
ation and follow instructions to bring the
device back online. Power Off / On the
press and resend the print job. If the
fault persists, contact the Customer
Support Center.

Either the DFA device is not
ready or another fault has oc-
curred with it

051-910, 051-911

Refer to the DFA device user document-
ation and follow instructions on how to
clear the fault and replenish the supplies.

The DFA device is either full or
out of supplies

051-912

Refer to the DFA device user document-
ation and follow instructions on how to
clear the fault. Set or change the profile
value (refer to the DFA user documenta-
tion). Power Off / On the press and re-
send the print job. If the fault persists,
contact the Customer Support Center.

Paper jam in the DFA device

051-913, 051-914,
051-915

Paper Jams

If a paper jam occurs, a fault screen displays a message on the press control panel
indicating in which area the jam is situated. Follow the instructions provided for clearing
the jam and resuming press operation.

Information about Paper Jams

Review the following list to address paper jams:

• When paper jams inside the press, the press stops and a fault message displays.
• Follow the instructions displayed on the screen to remove the jammed paper.
• Gently remove the paper taking care not to tear it. If paper is torn, be sure to remove

all torn pieces.

• If a piece of jammed paper remains inside the press, the paper jam message will

remain on the display.

• Paper jams can be removed with the press still powered on. When the power is turned

off, all information stored to the system's memory will be erased.

Xerox

®

Versant

®

2100 Press

10-28

User Guide

Problem Solving

Summary of Contents for Versant 2100









































































































































































































































































































Reviews:

No comments