manualshive.com logo in svg

Woodward ProTech-GII, Product Manual, Page: 41 / 195

Share
Download
Woodward ProTech-GII Product Manual Download Page 41

Manual 35086 

ProTech-GII with Math Functions 

 

 

 

Woodward 

39 

Torque range for screws of Screw 

Connection Terminal Blocks: 

0.22–0.25 N•m (1.95–2.21 lb-in). 

 

Screwdriver blade:  

0.4 X 2.5 mm (0.016 X 0.10 inch) 

Screwdriver available as 

Woodward PN 8992-005 

 

Figure 2-6. Screw Connection Terminal Block 

 
The ProTech-GII control’s terminal blocks are designed to be removed by hand. 
 
With circuit power and trip (interposing) relay controlled power disconnected, all terminal blocks can be 
removed, one at a time by unscrewing their terminal-locking screws and pulling them out of their sockets 
by hand. 
 

 

When removing a terminal block, never pull on the wires connected 
to the terminal block. 

 
Field wiring access for bulkhead mounted models is through gland plates located on the bottom of the 
enclosure. These gland plates allow users to bore multiple and different sized access holes for conduit entry, 
as required. Refer to Figure 2-3 for gland plate location and size. For EMI (electromagnetic interference) 
reasons, Woodward recommends that all low-voltage field wiring be separated from all high-voltage field wiring 
by using separate conduit and conduit entries into the ProTech-GII enclosure. Woodward also recommends 
that power wiring be segregated in the same manner, however LV and HV input power may be routed 
together. 
 
Field wiring access for panel-mounted models is located on the back of the ProTech-GII enclosure. To allow 
proper installation of the unit’s back cover plate, Woodward recommends that all field wiring be routed from the 
bottom of the package. The units back cover must be installed. Refer to Figure 2-5 for field wiring access 
information. For EMI (electromagnetic interference) reasons, Woodward recommends that all low-voltage field 
wiring be separated from all high-voltage field wiring where possible. Woodward also recommends that power 
wiring be segregated in the same manner, however LV and HV input power may be routed together. 
 

 

HIGH VOLTAGE—When wiring to interposing relays, be sure to wire 
both contacts with the same polarity. Failure to do so will create a 
potential shock hazard, which could cause injury or death. 

 

 

All input and output wiring must be in accordance with Class I 
Division 2 wiring methods, and in accordance with the authority 
having jurisdiction. 

 

All peripheral equipment must be suitable for the location in which it 
is being used. 

 

Released

Summary of Contents for ProTech-GII




































































































































































































Reviews:

No comments