manualshive.com logo in svg

Wiznet W7500, Reference Manual

The Wiznet W7500 Reference Manual is available for free download on our website. This comprehensive user manual provides detailed instructions and specifications for utilizing the Wiznet W7500 product efficiently. Enhance your understanding and maximize the potential of this exceptional device by downloading the manual from manualshive.com.

Share
Download
background image

 

W7500x Reference Manual Version1.1.0   

 

75 / 399 

IMR is used to mask interrupts. Each bit of IMR corresponds to each bit of IR. When a bit of 

IMR is ‘1’ and the corresponding bit of IR is ‘1’, an interrupt will be issued. In other words, if 

a bit of IMR is ‘0’, an interrupt will not be issued even if the corresponding bit of IR is ‘1’. 

[4] Magic Packet 

0: Disable Magic Packet Interrupt 

1: Enable Magic Packet Interrupt 

[5] PPPoE Close Interrupt Mask 

0: Disable PPPoE Close Interrupt 

1: Enable PPPoE Close Interrupt 

[6] Destination unreachable Interrupt Mask 

0: Disable Destination unreachable Interrupt 

1: Enable Destination unreachable Interrupt 

[7] IP Conflict Interrupt Mask 

 

0: Disable IP Conflict Interrupt 

1: Enable IP Conflict Interrupt 

 

IRCR (Interrupt Clear Register) 

Address Offset : 0x2108 

Reset value : 0x0000_0000 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

res 

res 

res 

res 

res 

res 

res 

res 

res 

res 

res 

res 

res 

res 

res 

res 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

res 

res 

res 

res 

res 

res 

res 

res

 

IRC[8:4] 

res 

res 

res 

res

 

 

 

 

 

 

 

 

 

*R/C_W1 

 

 

 

 

 

IRCR is used to clear interrupts. Each bit of IR can be cleared when the host writes ‘1’ value 

to each bit of IRCR corresponding to each bit of IR.   

* 

ReadClearWrite1 (R/C_W1) : Software can read as well as clear this bit by writing 

‘1’. Writing ‘0’ has no effect on the bit value. 

[4] Magic Packet Interrupt Clear 

[5] PPPoE Close Interrupt Clear 

[6] Destination unreachable Interrupt Clear 

[7] IP Conflict Interrupt Clear 

 

 

Summary of Contents for W7500
















































































































































































































































































































































































































Reviews:

No comments

Related manuals for W7500

Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Brand: Salusfin Pages: 6
Oracle Talari E1000 Installation Manual preview
Talari E1000
Brand: Oracle Pages: 24
Dentsply Sirona inLab Speedcure 9494800 Instruction Manual preview
inLab Speedcure 9494800
Brand: Dentsply Sirona Pages: 91
WHOOP WHT-25LT Quick Start Manual preview
WHT-25LT
Brand: WHOOP Pages: 26
JETWAY LI1B Series User Manual preview
LI1B Series
Brand: JETWAY Pages: 55
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Brand: EVOC Pages: 57
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Brand: AOpen Pages: 18
Supero SAS 846 TQ User Manual preview
SAS 846 TQ
Brand: Supero Pages: 16
IndigoVision Compact NVR-AS 4000 User Manual preview
Compact NVR-AS 4000
Brand: IndigoVision Pages: 38
TDK HHM Series HHM2409 Specifications preview
HHM Series HHM2409
Brand: TDK Pages: 2
Harman crown PIP Series Reference Manual preview
crown PIP Series
Brand: Harman Pages: 16
AMD Geode LX 800 User Manual preview
Geode LX 800
Brand: AMD Pages: 27
EXAGATE SYSGuard 6001 Quick Installation Manual preview
SYSGuard 6001
Brand: EXAGATE Pages: 7
Delta AH10EN-5A Series Operation Manual preview
AH10EN-5A Series
Brand: Delta Pages: 132
Miranda Imagestore Intuition+ User Manual preview
Imagestore Intuition+
Brand: Miranda Pages: 60
Hologic ThinPrep 3000 Operator'S Manual preview
ThinPrep 3000
Brand: Hologic Pages: 256
LanReady AP-952X User Manual preview
AP-952X
Brand: LanReady Pages: 40
Renesas PCA7755D User Manual preview
PCA7755D
Brand: Renesas Pages: 6

Brands by name

Popular brands

Load more brands