Wiznet W7500 Reference Manual Download Page 174

Page: 174 / 399

W7500x Reference Manual Version1.1.0

174 / 399

DMA channel request mask clear register
(DMA_CHNL_REQ_MASK_CLR)

Address offset : 0x024

Reset value : -

res

CHNL_REQ_MASK_CLR[5:0]

[Channel-1] CHNL_REQ_MASK_CLR – Set the appropriate bit to enable DMA requests for

the channel corresponding to dma_req[Channel-1] and dma_sreq[Channel-1]

This write only register enables a HIGH on dma_req[Channel-1], or dma_sreq[Channel-

1].

0 : No effect. Use the CHNL_REQ_MASK_SET register to disable

dma_req[Channel-1] and dma_sreq[Channel-1] from generating requests.

1 : Enables dma_req[Channel-1] or dma_sreq[Channel] to generate DMA

requests.

DMA channel enable set register (DMA_CHNL_ENABLE_SET)

Address offset : 0x028

Reset value : 0x0000_0000

res

CHNL_ENABLE_SET[5:0]

R/W

[Channel-1] CHNL_ENABLE_SET - Returns the enable status of channels or enables the

corresponding channels.

This read/write register enables a DMA channel. Reading the register returns the

enable status of the channels.

Read as :

0 – Channel [Channel-1] is disabled

Summary of Contents for W7500















































































































































































































































































































































































































Search results

Summary of Contents for W7500

Reviews:

Brands by name

Popular brands

Wiznet W7500, Reference Manual

Search results

Summary of Contents for W7500

Reviews:

Brands by name

Popular brands