Wiznet W7500 Page 186 Reference Manual Download

Page: 186 / 399

W7500x Reference Manual Version1.1.0

186 / 399

res

MASK

INT

R/W

[0] DONE – Interrupt bit

This bit indicates that conversion is done or not. This bit is set after conversion is done

and this bit is cleared by set of Interrupt clear bit. This bit is read-only.

[1] MASK – Interrupt mask signal.

This bit is interrupt mask bit of ADC. This bit can be set and cleared by S/W to

enable/disable interrupt mask.

0 : Interrupt disable

1 : Interrupt enable

ADC Interrupt Clear register (ADC_INTCLR)

Address offset : 0x01c

Reset value : 0x0000_0000

res

INTCLR

[0] INTCLR – Interrupt Clear bit.

This bit set by S/W to clear interrupt signal to CM0. This bit is write-only.

0 – nothing

1 – Clear interrupt signal (This bit clear automatically after clear interrupt)

Summary of Contents for W7500















































































































































































































































































































































































































Search results

Summary of Contents for W7500

Reviews:

Related manuals for W7500

Brands by name

Popular brands

Wiznet W7500, Reference Manual

Search results

Summary of Contents for W7500

Reviews:

Related manuals for W7500

Brands by name

Popular brands