Wiznet W7500 Page 175 Reference Manual Download

Page: 175 / 399

W7500x Reference Manual Version1.1.0

175 / 399

1 – Channel [Channel-1] is enabled

Write as :

0 – No effect. Use the CHNL_ENABLE_CLR register to disable a channel.

1 – Enables channels [Channel-1]

DMA channel enable clear register (DMA_CHNL_ENABLE_CLR)

Address offset : 0x02c

Reset value : -

res

CHNL_ENABLE_CLR[5:0]

[Channel-1] CHNL_ENABLE_CLR – Set the appropriate bit to disable the corresponding

DMA channel.

This write only register disable a DMA channel.

0 : No effect. Use the CHNL_ENABLE_SET register to enable DMA channel.

1 : Disable channel [Channel-1]

DMA channel primary-alternate set register
(DMA_CHNL_PRI_ALT_SET)

Address offset : 0x030

Reset value : 0x0000_0000

res

CHNL_PRI_ALT_SET[5:0]

R/W

[Channel-1] CHNL_PRI_ALT_SET - Returns the channel control data structure status, or

selects the alternate data structure for the corresponding DMA channels.

Summary of Contents for W7500















































































































































































































































































































































































































Search results

Summary of Contents for W7500

Reviews:

Related manuals for W7500

Brands by name

Popular brands

Wiznet W7500, Reference Manual

Search results

Summary of Contents for W7500

Reviews:

Related manuals for W7500

Brands by name

Popular brands