Wiznet W7500 Reference Manual Download

Page: 27 / 399

W7500x Reference Manual Version1.1.0

27 / 399

AHB-Lite BUS

This bus connects the Three masters (Cortex-M0 and uDMAC and TCP/IP

Offload Engine) and ten AHB slaves.

Two APB BUSs

These buses connect Seventeen APB peripherals (Watchdog, two Dual timers,

PWM, two UARTs, simple UART, two I2Cs, two SSPs, Random Number Generator,

Real Time Clock, 12bits Analog Digital Converter, Clock Controller, IO

Configuration, PAD MUX controller)

5.2

Memory organization

Introduction

Program memory, data memory, registers and I/O ports are organized within the same linear

4-Gbyte address space.

The bytes are coded in memory in Little Endian format. The lowest numbered byte in a word

is considered the word’s least significant byte and the highest numbered byte the most

significant.

Summary of Contents for W7500















































































































































































































































































































































































































Search results

Summary of Contents for W7500

Reviews:

Related manuals for W7500

Brands by name

Popular brands

Wiznet W7500, Reference Manual

Search results

Summary of Contents for W7500

Reviews:

Related manuals for W7500

Brands by name

Popular brands