Wiznet W7500 Page 359 Reference Manual Download

Page: 359 / 399

W7500x Reference Manual Version1.1.0

359 / 399

res

RXOI

TXOI

RXI

TXI

R/W R/W R/W R/W

[3] RXOI –Receive Overrun Interrupt

This bit depends on the state of the ROIE bit in the control register, UART2CR

[2] TXOI – Transmit Overrun Interrupt

This bit depends on the state of the TOIE bit in the control register, UART2CR

[1] RXI – Receive Interrupt

This bit depends on the state of the RXIE bit in the control register, UART2CR

[0] TXI – Transmit Interrupt

This bit depends on the state of the TXIE bit in the control register, UART2CR

UART2BDR (UART2 Baud Rate Divider Register)

Address offset: 0x010

Reset value: 0x0000_0000

The UART2BDR r is the integer part of the baud rate divisor value.

res

Res

res

R/W

BAUDDIV

R/W

[19:0] Baud rate divider

The minimum number is 16. These bits are cleared to 0 on reset

Example 1

If the required baud rate is 115200 and UARTCLK = 8MHz then:

Baud rate divisor BAUDDIV =

(𝐹

𝑈𝐴𝑅𝑇𝐶𝐿𝐾

/𝐵𝑎𝑢𝑑 𝑟𝑎𝑡𝑒)

Baud rate divisor =

(8 × 10

)/(115200) =

69.4

This means

BRD =

Summary of Contents for W7500















































































































































































































































































































































































































Search results

Summary of Contents for W7500

Reviews:

Related manuals for W7500

Brands by name

Popular brands

Wiznet W7500, Reference Manual

Search results

Summary of Contents for W7500

Reviews:

Related manuals for W7500

Brands by name

Popular brands