Wilo Sevio AIR P Installation And Operating Instructions Manual Download Page 18

18

 

WILO SE 02/2016 V06 DIN A4

English INTRODUCTION

1.  Introduction

1.1.  About this document

The language of the original operating instruc-

tions is German. All other languages of these 

instructions are translations of the original ope-

rating instructions.

This manual is divided into individual sections, 

which are listed in the table of contents. Each 

section has a meaningful heading which clearly 

describes its content.

1.2. 

Personnel qualifications

All personnel who work on or with the aeration 

system must be qualified for such work. All per

-

sonnel must be of legal age.

National accident prevention regulations must 

also be observed as a basis by the operating and 

maintenance personnel.

It must be ensured that personnel have read and 

understood the instructions in this operating and 

maintenance manual; if necessary, this manual 

must be ordered from the manufacturer in the 

required language.

This aeration system is not designed to be used 

by persons (including children) with impaired 

physical, sensory or mental capabilities or who 

have insufficient experience or knowledge to 

operate the unit.

Children should be supervised to ensure that they 

do not play with the aeration system.

1.3. 

Copyright

This operating and maintenance manual has been 

copyrighted by the manufacturer. The operating 

and maintenance manual is intended for use by 

installation, operating and maintenance person-

nel. It contains technical regulations and draw-

ings which may not be reproduced or distributed, 

either completely or in part, or used for purposes 

of competition, or shared with others without 

the express consent of the manufacturer. The 

illustrations used may differ from the original and 

are intended merely as an example representation 

of the aeration system.

1.4.  Subject to change

The manufacturer reserves the right to make 

technical modifications to systems and/or com

-

ponents. This operating and maintenance manual 

refers to the aeration system indicated on the 

title page.

1.5.  Warranty

In general, the specifications in the current “Gen

-

eral Terms and Conditions” apply to the warranty. 

You can find these here:

 

www.wilo.com/legal

Any deviations must be contractually agreed and 

shall then be given priority.

1.5.1.  General

The manufacturer is obliged to correct any 

defects found in the aeration system it sells, pro-

vided that the defects meet one or more of the 

following requirements:

• The defects are caused by the materials used 

or the way the product was manufactured or 

designed

• The defects were reported in writing to the 

manufacturer within the agreed warranty period

• The aeration system was used only as intended

1.5.2.  Warranty period

The duration of the warranty period is stipulated 

in the “General Terms and Conditions”.

Any deviations must be contractually agreed!

1.5.3. 

Spare parts, add-ons and modifications

Only genuine spare parts from the manufacturer 

may be used for repairs, replacements, add-ons 

and modifications. Unauthorised attachments and 

modifications, or the use of non-genuine parts, 

can lead to severe damage to the aeration system 

and/or to personal injury.

1.5.4.  Maintenance

The prescribed maintenance and inspection 

work should be carried out regularly. This work 

may only be carried out by qualified, trained and 

authorised personnel.

1.5.5.  Damage to the product

Damage and malfunctions that endanger safety 

must be eliminated immediately and properly by 

trained personnel. The aeration system may only 

be operated if it is in proper working order.

In general, repairs should only be carried out by 

Wilo customer service!

1.5.6.  Exclusion from liability

No warranty is granted and no liability is accepted 

for damage to the aeration system if one or more 

of the following apply:

• 

Inadequate configuration by the manufacturer 

due to the information provided by the operator 

or customer being insufficient or incorrect

• Sewage and air side fouling or scaling effects

• Non-compliance with safety instructions and 

working instructions as specified in this operating 

and maintenance manual

• Improper use

• Incorrect storage and transport

• Improper installation/dismantling

• 

Insufficient maintenance

• Incorrect repairs

• Inadequate construction site or construction work

• 

Chemical, electrochemical and electrical influ

-

ences

• Wear

This means the manufacturer’s liability excludes 

all liability for personal injury, material damage or 

financial losses.

2.  Safety

This section lists all the generally applicable 

safety instructions and technical information. In 

Summary of Contents for Sevio AIR P













































Reviews: