WhisperGen PPS16-12MD User Manual Download Page 13

Page: 13 / 84

Technical Specifications

How It Works

Feature

Specification

Remark

Cooling
system

Primary Cooling:
High quality marine grade
glycol-based corrosion-
inhibited anti-freeze for
freezing conditions.
Clean distilled water and high-
quality marine-grade
corrosion-inhibitor, suitable for
use with aluminium.

Removes heat from
engine.

Heat is transferred to
hot water cylinder(s)
and space heater(s).

Cooling method

Secondary Cooling:
Water-cooling (marine
applications).

Raw water cooling.

Heat
exchangers

Internal exhaust and marine
heat exchangers.

Requires external
coolant pump and
seawater pump.

Exhaust
temperature

80°C nominal, 95°C
maximum.

Cooling system extracts
heat from exhaust.

Connections

All connections
provided on the rear
panel of the enclosure.

Fuel

Rp 1/8 (ISO 7-1).

BSPP 1/8

Heat
exchangers

Rp 3/4 (ISO 7-1).

BSPP 3/4

Exhaust

Rp 1 1/4 (ISO 7-1).

Exhaust must be vented
outside occupied areas.

Exhaust flushing G 3/4 (ISO 228-1).

Face sealing fitting
required.

Condensate
draining

12.7mm O.D. plain tube.

Battery bank

50mm² screw terminals.

External switch

0.5 to 2.5mm² screw
terminals.

RJ 45.

Via RS485-to-RS232
converter.

Physical

Dimensions

450mm (W) x 500mm (D) x
650mm (H).

Dry weight

90kg.

Environmental

Temperature/
humidity

-10°C to 40°C. 99% RH, non-
condensing.

With suitable fuel and
coolants.

Summary of Contents for PPS16-12MD





















































































Search results

Summary of Contents for PPS16-12MD

Reviews:

Related manuals for PPS16-12MD

Brands by name

Popular brands

WhisperGen PPS16-12MD, User Manual

Search results

Summary of Contents for PPS16-12MD

Reviews:

Related manuals for PPS16-12MD

Brands by name

Popular brands