WhisperGen PPS16-12MD User Manual Download Page 84

Page: 84 / 84

Compliance Information

Responsibility for compliance

It is the responsibility of the person(s) installing the WhisperGen

and its

systems to ensure that it is installed in compliance with all laws, standards,
and regulations that apply in the country where the WhisperGen

installed. The installer must determine what laws and regulations apply.

European CE mark

The WhisperGen

is CE marked for applications where it is installed in

recreational craft. This means that in such an installation the WhisperGen

complies with the Essential Health and Safety Requirements of the relevant

European Commission Directives, which are:

•

Machinery Directive 98/37/EC

•

Electro Magnetic Compatibility Directive 2004/108/EC

•

Pressure Equipment Directive 97/23/EC

•

Waste Packaging Directive 94/62/EC

The installation of the WhisperGen

must comply with the Recreational

Craft

Directive 94/25/EC and the Amending Directive 2003/44/EC.

The

Recreational Craft Directive harmonised standards relevant to the
installation of the WhisperGen

are:

•

ISO 7840:2004 Small craft – Fire resistant fuel hoses

•

ISO 9093-1:1994 Small craft – Seacocks and through hull fittings,

metallic

•

ISO 9093-2:2002 Small craft – Seacocks and through hull fittings, non
metallic

•

ISO 9094-1:2003 Small craft – Fire protection for a hull up to 15 m in
length

•

ISO 10088:2001 Small craft – Permanently installed fuel systems and
fixed fuel tanks

•

ISO 10133:2000 Small craft – Electrical systems – Extra low voltage
DC installations

•

ISO 10240:1995 Small craft – Owners manual

•

ISO 16147: 2002 Small craft – Inboard diesel engines – engine
mounted fuel & electrical components

•

ISO 8528-10:1998 Noise – (meets specification of 50dBA at 7m)

Explosive environments

The WhisperGen

is not suitable for installation in spaces or

compartments

that require ignition-protected equipment.

Summary of Contents for PPS16-12MD





















































































Search results

Summary of Contents for PPS16-12MD

Reviews:

Related manuals for PPS16-12MD

Brands by name

Popular brands

WhisperGen PPS16-12MD, User Manual

Search results

Summary of Contents for PPS16-12MD

Reviews:

Related manuals for PPS16-12MD

Brands by name

Popular brands