WhisperGen PPS16-12MD User Manual Download Page 42

Page: 42 / 84

Displaying System Information

Operation

Installation Menu

Installation Menu

Parameter

Meaning

Typical Range

Heat exchanger Nozzle Bleed

Spraying water through the heat exchanger to clean
internal cavities.

On for 1 sec.

Air Bleed

Blowing air through the burner and exhaust system. ON or OFF (default).

Fuel Bleed

The fuel bleeding function – see section entitled
Bleeding the Fuel Line. The water pumps may start
when the fuel line is bled.

ON or OFF (default).

Coolant 1 Bleed

The coolant bleeding function – see section entitled
Bleeding the Coolant Circuit.

ON or OFF (default).

Coolant 2 Bleed

The seawater and coolant bleeding function – see
section 3.8.

ON or OFF (default).

Enable Starts

The function that enables or disables WhisperGen
starts during maintenance or servicing. "0" = "no
starts allowed"; "1" = "allow manual starts only"; "2"
= "allow all manual and automatic starts".

0 (default), 1 or 2.

Summary of Contents for PPS16-12MD





















































































Search results

Summary of Contents for PPS16-12MD

Reviews:

Related manuals for PPS16-12MD

Brands by name

Popular brands

WhisperGen PPS16-12MD, User Manual

Search results

Summary of Contents for PPS16-12MD

Reviews:

Related manuals for PPS16-12MD

Brands by name

Popular brands