WhisperGen PPS16-12MD User Manual Download Page 60

Page: 60 / 84

Replacing Fuses

Maintenance

4. Remove the appropriate fuse and check if it has blown. The fuses are

located at the bottom of the electronics enclosure and are marked with
their current ratings in Ampere. Error codes displayed on the control
panel help identify which circuit and therefore which fuse may possibly
have blown.

Current Rating
in Ampere

External / Auxillary

Seawater Pump &
Coolant Pump Circuits

Internal Coolant Pump
Circuit

Fuel Pump & Fuel
Shut-off Valve Circuits

Air Blower, Oxygen Sensor,
& Flushing Circuits

Control Panel &
Microcomputer Circuits

Glow Plug Circuit

WTL0038

32A

5. Replace the faulty fuse.

6. Replace the electronics enclosure cover and fasten the four screws.

7. Replace the enclosure lid.

8. Reconnect

the

WhisperGen

to the battery bank by closing the circuit

breaker.

Note that WhisperGen

fuses can be obtained from electrical hardware

suppliers or your authorised WhisperGen

service agent.

Summary of Contents for PPS16-12MD





















































































Search results

Summary of Contents for PPS16-12MD

Reviews:

Related manuals for PPS16-12MD

Brands by name

Popular brands

WhisperGen PPS16-12MD, User Manual

Search results

Summary of Contents for PPS16-12MD

Reviews:

Related manuals for PPS16-12MD

Brands by name

Popular brands