WhisperGen PPS16-12MD User Manual Download Page 22

Page: 22 / 84

Introduction

Operation

Introduction

This section outlines the procedure for operating your WhisperGen

. It will

show you how to:

Start and stop the WhisperGen

;

Charge the battery bank;

Manage

heat

generation;

Clear faults and warnings;

Adjust the contrast of the LCD; and

Display and edit system parameters of the WhisperGen

You should read and understand all safety precautions before

operating your WhisperGen

Installing the WhisperGen

To install the WhisperGen

, contact your authorised WhisperGen

service agent.

The WhisperGen

must be installed and commissioned by an

authorised WhisperGen

service agent. If you install the WhisperGen

yourself, the warranty will be void. Incorrect installation may damage the
WhisperGen

and property, and/or cause personal injury.

Quick Reference - Operating Options

Depending on the options selected, the WhisperGen

may stop running

before or after the battery bank is charged, as shown in the table below.

Heat Manage ON

Heat Manage OFF

WhisperGen

starting
method

Max Run
Hours

< 25

Max Run
Hours

= 25

Max Run
Hours

< 25

Max Run
Hours

= 25

Manual start

Remote switch
start with

Ext

Cont Mode

set to 1

Continues
running until
stopped by
the user.

Remote switch
start with

Ext

Cont Mode

set to 2*

Stops when

Max Run
Hours

value

is reached,
even if the
battery bank
is not yet
fully
charged.

Continues
running until
stopped by
the user or
remote
switch.

Stops when
the battery
bank is
charged or
when

Max

Run Hours

value is
reached,
which ever
comes first.

Continues
running until
the battery
bank is
charged,
then stops.

Auto-charge

start

Stops when the battery bank is charged, regardless of

Max Run Hours

and

Heat Manage

settings.

In all cases, the WhisperGen

can be stopped at any time by pressing

STOP

on the control panel.

* In this mode, the WhisperGen

will run for at least one hour.

Summary of Contents for PPS16-12MD





















































































Search results

Summary of Contents for PPS16-12MD

Reviews:

Related manuals for PPS16-12MD

Brands by name

Popular brands

WhisperGen PPS16-12MD, User Manual

Search results

Summary of Contents for PPS16-12MD

Reviews:

Related manuals for PPS16-12MD

Brands by name

Popular brands