Wexxar WF-10T Operation And Service Manual Download Page 107 | Manualshive

Page: 107 / 156

background image

WF-10T

Case Former

Machine Maintenance

9-95

9.10.2 Conveyor Drivebelt Repairs

To change the drivebelts,

1) Slacken the belt-tensioning nuts to the fully

BACK

position. This will permit belt removal

by starting at the idle pulley end, and lifting the belt off upwards and back.

2) Replace with a new belt.

3) Make marks 25" apart on the belt before any load is applied.

4) Tension the belt by tightening the tensioning screws equally to achieve a measurement of

25¼" between the marks (1 percent stretch).

5) Run the belts to ensure correct tracking. If necessary, tighten the tensioning screw on

the side that the belt moves towards.

9.10.3 Drivebelt Bearings Repairs

All drivebelts run on sealed ball bearings, which are lubricated for life. Should bearing failure
occur, the entire bearing and housing should be replaced.

9.10.4 Gearmotor Repairs

Should failure of these components occur, replacement is recommended. The gearmotor shaft
‘plugs into’ the drive pulley that is mounted to the conveyor bottom plate. Refer to the assembly
drawing in the Supplementary Manual for more information and part numbers.

«
...
105
106
107
108
109
...
»

Summary of Contents for WF-10T





























































































































































Reviews:

No comments

Related manuals for WF-10T

Brand: NARGESA Pages: 33

Brand: GE Pages: 14

Brand: GE Pages: 11

Brand: GE Pages: 20

Druck ADTS 2 Series

Brand: GE Pages: 18

Brand: Cannon Pages: 40

Brand: NARGESA Pages: 34

Brand: RayLight Pages: 34

GAZELLE FREESTYLE

Brand: Gazelle Pages: 10

Brand: Latham Pages: 19

Brand: J.P. SELECTA Pages: 32

Brand: PAS Systems International Pages: 24

MARK V Alcovisor

Brand: PAS Systems International Pages: 20

Brand: PARRY Pages: 14

Brand: York Fitness Pages: 36

Brand: H&S Pages: 54

Brand: Samson Pages: 2

Brand: Gardco Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands