Wexxar WF-10T Operation And Service Manual Download Page 9

Page: 9 / 156

WF-10T Case Former

Table of Figures

vii

Figure 5-40: 'Alarm History' Screen........................................................................................... 5-36

Figure 5-41: 'CLEAR' Button ..................................................................................................... 5-36

Figure 5-42: ‘Password’ Window ............................................................................................... 5-36

Figure 5-43: 'Alphanumeric Keypad’ Window............................................................................ 5-36

Figure 5-44: ‘PREVIOUS’ Button............................................................................................... 5-36

Figure 5-45: 'Service' Button ..................................................................................................... 5-37

Figure 5-46: 'TROUBLESHOOTING’ Button ............................................................................. 5-37

Figure 5-47: 'Troubleshooting' Screen ...................................................................................... 5-37

Figure 5-48: 'PLC INPUTS’ Button ............................................................................................ 5-37

Figure 5-49: 'PLC Inputs’ Screen .............................................................................................. 5-38

Figure 5-50: 'PLC Inputs’ Status Indicator................................................................................. 5-38

Figure 5-51: PLC Input Status Indicator Illuminated.................................................................. 5-38

Figure 5-52: 'PLC OUTPUTS’ Button ........................................................................................ 5-38

Figure 5-53: 'PLC Outputs' Screen............................................................................................ 5-39

Figure 5-54: 'PLC Outputs’ Status Indicator .............................................................................. 5-39

Figure 5-55: PLC Output Function Indicator Illuminated ........................................................... 5-39

Figure 6-1: Walk-In Magazine ................................................................................................... 6-44

Figure 6-2: Magazine Pusher .................................................................................................... 6-45

Figure 6-3: Magazine Pusher in Locked Position...................................................................... 6-45

Figure 6-4: Discharge Pusher Before and After Adjustment ..................................................... 6-45

Figure 6-5: Discharge Pusher Adjustment Wingnuts ................................................................ 6-45

Figure 7-1: Case Size Adjustment and Jawplate Adjustment Instruction Labels...................... 7-51

Figure 7-2: Case Dimension Measurements............................................................................. 7-52

Figure 7-3: Case Size Range Dimensional Diagram................................................................. 7-53

Figure 7-4: Dimension ‘A’ Hand Crank...................................................................................... 7-54

Figure 7-5: Dimension ‘A’ Pointer.............................................................................................. 7-54

Figure 7-6: Magazine Width ...................................................................................................... 7-54

Figure 7-7: Vertical Adjustment Chain Lock .............................................................................. 7-55

Figure 7-8: Dimension ‘M’ Hand Crank ..................................................................................... 7-55

Figure 7-9: Dimension ‘M’ Pointer ............................................................................................. 7-55

Figure 7-10: Dimension ‘B’ Vertical Adjustment Chain Lock..................................................... 7-56

Figure 7-11: Dimension ‘B’ Pointer on Injector Backplate......................................................... 7-56

Figure 7-12: Dimension ‘B’ Hand Crank.................................................................................... 7-56

Figure 7-13: Dimension ‘D1’ Hand Crank.................................................................................. 7-57

Figure 7-14: Dimension ‘D1’ Pointer.......................................................................................... 7-57

Figure 7-15: Measuring Parallel Jawplate Width....................................................................... 7-57

Figure 7-16: Jawplate Formed Case Width 'D1' Adjusts ........................................................... 7-58

Figure 7-17: Improperly Adjusted Synchronizer Bar ................................................................. 7-58

Figure 7-18: Properly Adjusted Synchronizer Bar ..................................................................... 7-58

Figure 7-19: Divergent Jawplates.............................................................................................. 7-58

Figure 7-20: Parallel Jawplates ................................................................................................. 7-58

Figure 7-21: Jawplate and Carriage Assemblies....................................................................... 7-60

Figure 7-22: Ringpins and Horizontal Pinblock Adjustment Wingnuts ...................................... 7-60

Figure 7-23: Outer (left) and Inner (right) Pins Engaged........................................................... 7-62

Figure 7-24: Pin & Dome Position Adjustments ........................................................................ 7-63

Figure 7-25: Clearance Between Rear Flap and Center Ski..................................................... 7-64

Figure 7-26: Bottom Center Ski ................................................................................................. 7-64

Figure 7-27: Dimension ‘D3’ Case Width Adjust ....................................................................... 7-65

Figure 7-28: Case Width Verification......................................................................................... 7-65

Figure 7-29: Dimension ‘C’ Formed Case Length Adjust.......................................................... 7-66

Figure 7-30: Jawplate and Carriage Assemblies....................................................................... 7-66

Figure 8-1: Serpentine Chain Drive........................................................................................... 8-71

Figure 8-2: Conveyor Belt Tensioning....................................................................................... 8-77

Figure 8-3: Inductive Sensor Adjustment Range....................................................................... 8-78

Figure 9-1: Lowering the Tape Head Bracket ........................................................................... 9-89

Figure 9-2: Elevating the Tape Head Bracket ........................................................................... 9-91

Summary of Contents for WF-10T





























































































































































Search results

Summary of Contents for WF-10T

Reviews:

Related manuals for WF-10T

Brands by name

Popular brands

Wexxar WF-10T, Operation And Service Manual

Search results

Summary of Contents for WF-10T

Reviews:

Related manuals for WF-10T

Brands by name

Popular brands