Wexxar WF-10T Operation And Service Manual Download Page 88

Page: 88 / 156

WF-10T

Case Former

Machine Maintenance

- 8-76 -

Every 3 Months

Thoroughly clean all adjustment screws, sprockets, chain and sliding components, and then
lightly grease. See Section 8.6:

‘Lubrication’

for correct grease.

•

Lubricate width and height adjustment leadscrews with Food Grade Fuchs Geralyn FMG

387 lubricant.

•

Remove drivebelts. Drive pulleys and idler pulley should be inspected for bearing wear

and pulley damage. Remove any dirt build-up before drivebelts are re-installed.

•

Remove flap folders for servicing. Remove covers and check for worn parts.

•

Check the tension of the Uni-Drive side-belt chain drive.

•

Inspect all pneumatic and electrical limit switches and verify that they are properly

adjusted and in good working order.

•

Check for any loose or missing fasteners.

NOTE: Proper tension for the Uni-Drive side-belt chain
drive is achieved when the horizontal sag in the chain
measures between 1/8” and ¼” with the drivebelts in a fully
opened position.

Summary of Contents for WF-10T





























































































































































Search results

Summary of Contents for WF-10T

Reviews:

Related manuals for WF-10T

Brands by name

Popular brands

Wexxar WF-10T, Operation And Service Manual

Search results

Summary of Contents for WF-10T

Reviews:

Related manuals for WF-10T

Brands by name

Popular brands