W&H Med lina Instructions For Use Manual Download Page 25

Page: 25 / 114

COMMON COMMANDS AND ICONS

Icon

Function

Enters/exits the standby mode.

Moves to the previous/next screen.

Opens the homepage.

Accesses to the sub-menus.

Provides access to the setting
screen of a specific area.

Shows the list of all operating
parameters of the sterilizer.

Opens a screen with other
settings/options.

Icon

Function

Refreshes the page.

Indicates the value that may be
changed and appears by clicking on
it.

Confirm the active option.

Saves a setting or a
parameter.

Answers YES to a question.

Aborts the action/function.

Moves to the previous screen
without confirming/making
any changes nor saving any
parameters.

Answers NO to a question.

Indicates that the AUTO DRY mode is
operating.

Optional, activated with an activation
code. Indicates that the ECO DRY plus
mode is operating.

Increases/decreases the value.

Icon

Function

Indicates that an error occurs.

Indicates that the option checked is
working properly.

Plays a video.

Starts a procedure.

Pauses a video.

Indicates that the chamber door is
locked.

Indicates that the chamber door is
locking/unlocking.

Indicates that the chamber door is
unlocked and can be open.

Programs a succession of cycles for
daily repetition.

Indicates that the option is ON and
allows to set it OFF by touching it.

Getting started

Summary of Contents for lina



















































































































Search results

Summary of Contents for lina

Reviews:

Related manuals for lina

Brands by name

Popular brands

W&H Med lina, Instructions For Use Manual

Search results

Summary of Contents for lina

Reviews:

Related manuals for lina

Brands by name

Popular brands