W&H Med lina Instructions For Use Manual Download Page 18 | Manualshive

Page: 18 / 114

background image

18

LINA | Instructions for Use | RIK-1 Med ENG Rev03 | 11/05/2020 | © 2020 W&H Sterilization Srl

Getting started

Installing the sterilizer

LOCATION REQUIREMENTS

Notice:
Do not place the sterilizer so that it is difficult to operate the
controls behind the service door. Do not place the sterilizer so that
it is difficult to disconnect the power supply plug.
Leave the condenser grid (rear side of the sterilizer) free from
anything that might obstruct the air passage.
Surface materials should be water resistant. If sterilization cycles
will be continuous, pay attention to the surrounding materials:
steam can damage them.
The sterilizer must operate in absence of explosive atmospheres.
The sterilizer must operate in a well ventilated room (indoor), far
from sources of heat and from flammable materials.
Place the sterilizer on a flat and level surface.

Clearance requirements to ensure proper air circulation:

ELECTRICAL CONNECTIONS

All the cables and tubes connected on the rear side of the sterilizer
must be placed far from the condenser grid (e.g. using the available
guides).

Notice:
Connect the sterilizer to a dedicated line. Do not use cable
extensions nor multiple sockets/adapters.
Ensure that external and internal surfaces are free from moisture or
condensation before connecting to power.

«
...
16
17
18
19
20
...
»

Summary of Contents for lina



















































































































Reviews:

No comments

Related manuals for lina

Relion 670 series

Brand: ABB Pages: 66

Brand: Hanil Pages: 60

Brand: SALUDA MEDICAL Pages: 61

Brand: ACCU-CHECK Pages: 104

Brand: Gary Machinery Pages: 14

Brand: Nabtesco Pages: 26

Brand: National Instruments Pages: 10

Brand: Parker Pages: 64

Brand: Parker Pages: 40

Matrx Digital MDM

Brand: Parker Pages: 20

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 178

Brand: Yamaha Pages: 15

Brand: Daekyung Pages: 15

Brand: RAM Pages: 4

Brand: SAC Pages: 2

Brand: REED Pages: 12

LED PL G24d TC-D

Brand: Bailey Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands