Volvo SDLG LG956L Operation & Maintenance Manual Download Page 98

Page: 98 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

3.6.2 Adding Fuel to Fuel Tank

Fuel Level Check

Park the machine on level

ground, and check the fuel

level by dipstick on the outside

of fuel tank. If the fuel level is

under 0, please add fuel from

inlet on the fuel tank. For fuel

selection please refer to

CHAPTER IV 2.2

Selection of Oil, Fuel and

Coolant

3.6.3 Adding Oil to Gearbox

①

Oil Level Check

Park the machine on level ground and put the transmission

lever in the

neutral

(“

”) position. Pull the brake valve

manual control handle or press the parking brake switch to

carry out braking, and wedge the front and back of the tire.

Start engine and let the engine run in the idle status for

several minutes. Open the oil checking plug at the side of

the transmission box, the oil level is normal if there is oil

flowing but not form pressure; if there is not oil flowing,

hydraulic transmission oil should be added. The choice of the hydraulic transmission oil can be

found in

CHAPTER IV 2.2 Selection of Oil, Fuel and Coolant

②

New Oil Replacement

Park the machine on level ground and put the transmission

lever in the

neutral

(“

”) position. Pull the brake valve

manual control handle or press the parking brake switch to

carry out braking, and wedge the front and back of the tire.

Start the engine and run in the idle status for several

minutes. Loosen the oil drain plug on the side of the

gearbox to drain the oil, and contain it with container.

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands