Volvo SDLG LG956L Operation & Maintenance Manual Download Page 101

Page: 101 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

3.6.5 Adding Oil to Hydraulic Oil Box

①

Oil Level Check

Park the machine on level ground and lower the bucket

to the ground. Check whether there is an angle between

front and rear frame.

Check the oil level indicator of the hydraulic oil box on

the left side of the machine. The oil level is normal if the

level indicator scale is at a range of 12±2. If the oil level

indicator is lower than scale 10 of the middle scale, please add hydraulic oil. Refer to

CHAPTER IV 2.2

Selection of Oil, Fuel and Coolant

for selection of oil.

②

Oil Replacement

△

WARNING

While replacing oil if other maintenance needs to be done do

so following the relevant rules, and pay attention to safety.

△

NOTICE

Pay attention to the clarity of the oil while replacing it;

never

let other materials enter the hydraulic system directly.

Clean out the in bucket. Park the machine on level ground and put the transmission lever in the

neutral

position. Pull the brake valve manual control handle or press the braking control lever to

carry out braking. Start the engine and keep in the idle status for 10 minutes. Raise and lower the

lift arm several times, and tilt the bucket forward and backward several times.

Raise the lift arm to the highest position; tilt the bucket backwards to the extreme position and

shut the engine.

Push the bucket control lever forward to let the bucket tilt forward freely by its weight. Drain out

the oil in the bucket cylinder. After the bucket has tilted to the desired position, push the lift arm

control lever forward to let the lift arm fall down by its weight freely. Drain out the oil in the lift

arm cylinder.

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands