Volvo SDLG LG956L Operation & Maintenance Manual Download Page 119

Page: 119 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

114

cartridge in the oil pan of gearbox. Replace the filter cartridge in the oil lines of torque

converter-gearbox. Replace the gearbox oil.

Replace the gear oil in the front and rear axles.

Check if there is leakage in the brake system. Clean the filter mesh of the oil bowl in the booster

pump. Clean the air vent and check the brake fluid. Add them if deficient and replace them if

necessary.

3.4 Every 500 Hours (Season) Service

Carry out the periodic maintenance of every 10, 50 and 250 hours with this maintenance operation at

the same time.

Check and adjust the clearance of hand brake system.

Check the wear condition of brake discs and friction discs. Replace them if necessary.

Clean the silencer of the braking electromagnetic valve.

In addition, do the extra maintenance in the first 500 hours as follows:

Check if there is leakage in the hydraulic system. Check and clean the air vent of hydraulic

reservoir. Replace the oil-return filter cartridge and pilot filter of hydraulic reservoir. Check the

quantity and cleanness of hydraulic oil. Filter the oil if possible. Add them if deficient and replace

them if necessary.

Check if there is leakage in the brake system. Clean the filter mesh of the oil bowl in the booster

pump. Clean the air vent and replace the brake fluid.

3.5 Every 1000 Hours (Half a Year) Service

Carry out the periodic maintenance of every 10, 50, 250 and 500 hours with this maintenance

operation at the same time.

Clean the oil pan of gearbox. Clean the air vent of gearbox. Replace the suction filter cartridge in

the oil pan of gearbox. Replace the filter cartridge in the oil lines of torque converter-gearbox.

Replace the gearbox oil.

Change the gear oil in the front and rear axles.

Replace the antifreeze (replace once every 1000 hours or 1 year, choose according to which

comes earlier).

Check and clean the filter of the reinforcing pump oil storage cup, and clean the air vent to

replace the brake fluid.

Check if there is leakage in the hydraulic system. Check and clean the air vent of hydraulic

reservoir. Clean the hydraulic reservoir. Replace the oil-return filter cartridge and pilot filter of

hydraulic reservoir.

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands