Volvo SDLG LG956L Operation & Maintenance Manual Download Page 69

Page: 69 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

Air Pressure Gauge

This gauge indicates the air pressure of the brake system.

If the pressure index lies in the green range (0.4MPa~0.8MPa), the

oil pressure is normal. Be sure to stop the machine for inspection if

the index moves outside this range.

If the pressure index lies in the range of (4~8)×100kPa or

(5.8~11.6)×10PSI, the oil pressure is normal. Be sure to stop the

machine for inspection if the index moves outside this range.

Fuel Level Gauge (if assembled)

This gauge indicates the ratio of remaining fuel level in the fuel tank to

the volume of tank.

Revolution Indicator (if assembled)

This gauge indicates the rotating speed of engine.

Indicator Lamp

The indicator lamp is located on the gauge panel. Refer to

1.1

Control Systems and Gauges Figure3-3 and 3-4

in this chapter.

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands