Volvo SDLG LG956L Operation & Maintenance Manual Download Page 77

Page: 77 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

1.2.5 Cab Door Locking Bar

Outside Cab Locking Bar:

Open the left and right door to 180° and the orientation lock on the

door will touch the outside lock of the cab

and the door will be locked outside the cab.

Turn the control bar downward and it will

unlock.

Inside Cab Locking Bar:

When the lock of

the cab is in the locked positions, the door

will be locked automatically after closing the door. Insert key outside the cab. Turn

180°clockwise and pull out key. Pull the handle outside the cab and the cab door will open. Turn

the lock bar upward and it will open.

1.2.6 Frame Locking Bar

△

! WARNING

Be sure to use the front and rear frame locking bar during

maintenance or transporting the machine.

Be sure to release the frame locking bar during routine travel.

The frame locking bar is used to lock the front and rear frames during maintenance or

transporting vehicles, in order to prevent the frames from moving.

1.2.7 Towing Pin

During towing, insert the towing pin

①

into the counterweight .

②

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands