Volvo SDLG LG956L Operation & Maintenance Manual Download Page 8 | Manualshive

Page: 8 / 130

background image

Operation & Maintenance Manual

──

LG956L Wheel Loader

III

SAFETY INFORMATION

Operators should know and obey the safety criteria described in national and local laws. If there is no

such national or local criteria, please follow the rules described in this manual.

Most accidents are caused by the failure to follow fundamental safety regulations for the operation

and maintenance of machines. To avoid accidents, please read, understand and follow all precautions

and warnings in this manual about the machine before performing any operation or maintenance.

Safety precautions are specified in SAFETY of Chapter I, page 1.

Safety information described in this manual cannot include safety precautions for every circumstance

that might involve a potential hazard in operation and maintenance. Therefore, if procedures or

actions which are not recommended in this manual are used, the safety of the operator and machine

must be confirmed. Otherwise, consult us or the dealers.

The safety precautions for operation and maintenance in this manual only apply to those conditions

specified by the machine. If the uses of the machine are not specified in the manual, users should

assume full responsibility for their actions. We will not bear any safety responsibility for the operators

or machine.

In any case, you should not engage in prohibited operations as described in this manual.

The following signs are used for identification of safety information in this manual:

△

!

DANGER

──

This word is used in safety messages and on safety labels where there is a

high possibility of serious injury or death if the hazard is not avoided. These safety messages or
labels usually describe precautions that must be taken to avoid the hazard. Failure to avoid this
hazard may also result in serious damage to the machine.

△

!

WARNING

──

This word is used in safety messages and on safety labels where there is

a potentially dangerous situation. Failure to avoid this hazard may also result in serious injury or
death. Failure to avoid this hazard may also result in serious damage to the machine.

△

!

NOTICE

──

This word is used in safety messages and on safety labels for the hazards

that could result in minor or moderate injury if the hazard is not avoided. This word is used for
precautions that must be taken in order to avoid actions which could shorten the life of the
machine.

«
...
6
7
8
9
10
...
»

Summary of Contents for SDLG LG956L



































































































































Reviews:

No comments

Related manuals for SDLG LG956L

Brand: Genie Pages: 64

Brand: Scag Power Equipment Pages: 29

Brand: Case Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands