Volvo SDLG LG956L Operation & Maintenance Manual Download Page 49

Page: 49 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

battery contains vitriol. So mis-operation of the storage battery may lead to severe injury or fire.

Please do as follows:

Keep kids away from the battery. Wear safety glasses and rubber gloves to deal with the battery.

If vitriol gets in the eyes or on the clothes or wash with lots of water and go to hospital if hurt

severely.

Keep fire away from the battery during charging because the generation of oxygen and hydrogen

may cause an explosion. Prevent circuit from shorting.

Keep fire away from the crust on the battery because it is flammable.

Store the battery under dry, clean and well ventilated circumstances with temperatures between

5~25

℃

. Prevent sun light irradiation. Keep the battery 2m away from a heat source. The battery

will be affected by high temperature.

Never

reverse and put horizontally. Prevent damage by too much pressure.

The storage life of a battery is 6 months under room temperature without charging. If over 6

months, please charge before use.

Pay attention to the labels on equipment before installation to prevent accidents.

Spread vaseline on the poles to prevent erosion. The wire connections should be firm and

credible.

Never

hammer the wire pole which may cause the leak of vitriol.

Connect the positive pole of the storage battery with the negative pole of the machine first, and

then connect the negative pole of the storage battery with the positive pole of the machine.

Put the battery on the shaft using the upside fixing method or downside fixing method to prevent

destruction caused by loosening.

There is an indicator on the cover of the battery. The green light means it can be used, the black

light means it should be charged, and the white light means it should be replaced. Replace with a

new battery after the white light indicator.

Routinely recharge the battery if the battery lacks electric power during use to prevent the

capability of battery sulfate going down.

If the battery is installed, disassemble it and put it in a dry and well ventilated place if it is not

used for long time (generally more than 15 days). Recharge the battery every 3~6 months (based

on whether the indicator is black or not).

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands