Volvo SDLG LG956L Operation & Maintenance Manual Download Page 97

Page: 97 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

Rotate the oil drain plug and let the oil

flow out and hold it in a container.

Change the oil filter.

After the oil is released completely, rotate

the oil drain plug back.

Add engine oil from the oil adding port.

Weichai WD10G220E13 engine:

Open the left side door of the engine hood; add prescribed

engine oil (about 12L) from oil adding port of engine.

Shangchai C6121ZG50B engine:

Open the right side door of the engine hood; add

prescribed engine oil (about 27.5L) from oil adding port of engine.

Cummins 6CTA8.3 engine:

Open the right side door of the engine hood; add prescribed

engine oil (about 27.5L) from oil adding port at the side of engine or from the oil adding

port on the top of engine when open the left door of the engine hood.

Run the engine at idle status, check whether the oil filter and oil releasing plug are leaky.

After the engine was stopped for 15 minutes, let the engine oil flow back to the oil pan, and check

the engine oil level of the engine again.

③

Engine oil Filter Replacement

Disassemble

Clean the area near the engine oil filter. Disassemble it with filter elements spanner.

Assemble

Add diesel oil full in the filter element and smear engine oil on the rubber seal ring.

Tighten 3/4~1 cycles after the seal ring connects with the base.

Start the engine and check whether the seal ring is seal. If not, disassemble the filter element and

check the sealing surface.

△

NOTICE

After changing the filter elements, the engine must run in the idle

status at least 1 minute to ensure the engine is lubricated

sufficiently before working.

Over tight mechanical rotation could damage the screw thread or

filter element sealing.

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands