Volvo SDLG LG956L Operation & Maintenance Manual Download Page 100

Page: 100 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

②

Oil Replacement

Park the machine on level ground and run in idle status for about 10 minutes. Trample the

accelerator gently to move the machine slowly to let the oil drain plug on the wheel side of the

front axle go to the lowest position

Shut engine. Push transmission lever in the

neutral

(“

”) position. Pull the brake valve manual

control handle or press the parking brake lever to carry out braking, and wedge the front and rear

wheels.

Loosen the oil drain plugs on the two wheels on the end sides of the front axle and the oil drain

plugs at the center bottom of the axle shell to drain oil to the container.

△

WARNING

The temperature of gear oil may be high, so wear protective

clothes, and operate it carefully to prevent injury.

Drain out all the old oil and screw tight the oil drain plugs at the center bottom of the axle shell.

Start engine. Press the brake valve manual control handle or rotate the parking brake switch until

it rebounds to release the brake. Move the machine slowly with gentle acceleration to let the oil

draining port at the end of wheel side move into the horizontal position, and then shut the engine.

Put the transmission lever in the

neutral

position. Pull the brake valve manual control handle or

press the parking brake switch to carry out braking.

Add new gear oil from the oil drain port at the end of two wheels sides of the front axle and the

oil inlet port at the middle of the axle shell (about 32L). And then check the oil level again.

Tighten the oil drain plugs at the end of two wheels sides of the front axle and the oil adding plug

at the middle of the axle shell.

Replace the rear axle gear oil according to the procedures above.

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands