Volvo SDLG LG956L Operation & Maintenance Manual Download Page 78

Page: 78 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

1. Working Indicator Lamp 2.Air Volume and Power Switch
3. The Switch to Control the Temperature

1.2.8 Fuse

△

NOTICE

Always be sure to close the startup switch before replacing the

fuse .The fuse is used to protect the wiring and cable from burning

out. If the fuse has become corroded by oxidation, or the fuse is

loose in the fuse holder, please replace the fuse.

When replacing the fuse, please replace with a fuse of the same

specification.

1.2.9 Air Conditioning (if assembled)

The Appearance of Panel

The panel of air conditioning is at the right side of cab’s seat.

1.2.9.1

Ⅰ

control panel and is operation (if assembled)

Operating methods

a) Refrigeration

Start the engine.

Open the air volume and power

switch 2 which have three gears (fan

low gear, fan middle gear and fan

high gear) and four positions (O, L,

M and H). The speed of evaporating

fan increases from left to right to

adjust the air volume.

Open the temperature control switch

3 to the max (the indicator lamp 1 will light), then the compressor starts working for the

refrigeration of air conditioning.

Turn the air volume and power switch 2 to select different gear to obtain three different

volume of air.

Turn the temperature control switch anticlockwise slowly to obtain the desired temperature

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands