Volvo SDLG LG956L Operation & Maintenance Manual Download Page 81

Page: 81 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

automatically after pushing it down.

Backrest Angle Adjustment

Put the backrest angle adjust handle C upward to pull the backreat until the angle is comfortable. The

backrest angle is locked when loose the handle.

Height Adjustment

There are three positions for the height of seat, and the operator can adjust according to the need.

During adjusting, set the base under the seat by two hands and draw up forcibly and stably. When the

cracking sound is sounded, please loose your hands, then the seat will fix in this position. Adjust the

position of seat to the highest position and draw up forcibly, and then press down, the seat will fall to

the lowest position.

Headrest Height Adjustment

Set the headrest of seat by two hands, and then draw up or press down forcibly to adjust the height of

headrest.

1.2.11 Use of Safety Belt (if assembled)

If the safety belt is assembled on the seat, please tie it when operating the machine. Before using

safety belt, please check the degree of wear and firm. Replace it if it is necessary.

Adjust the length of safety belt before using to make sure the safety belt can be used for safety

guarantee and comfort. Move the position of lock on the safety belt to adjust the length of safety belt.

The clamper of the safety belt is at the right side of seat, and put the lock into the opening of clamper

to jam the lock. There is a red button on the side of opening of clamper. Press the button and the lock

will jump out from the clamper. Before using the safety belt, please check the clamper of safety belt

whether lock and loose normally.

1.2.12 Rearview Mirror

Rearview mirrors are on the left and right sides outside the cab. Before starting work, the rearview

mirror must angle be adjusted for a good rear.

1.2.13 Key

This loader equips two key for every using condition:

The starting switch key for engine.

The key of left and right doors of cab.

The key of left and right doors of engine hood.

The key of left and right otter boards of engine hood.

The key for adding fuel port of fuel box (if mounted).

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands