manualshive.com logo in svg

Vmac G300004, Installation, Owners And Service Manual, Page: 79 / 112

Share
Download
Vmac G300004 Installation, Owners And Service Manual Download Page 79

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

77

Pressure Control Tubes

A 1/4 in PTFE tube (shown in light blue) connects the discharge valve to the lower 

fitting on the side of the compressor inlet valve. This provides the system air 

pressure (factory setting 140 psi) to operate the inlet poppet valve (Figure 50). 

Figure 50  —  1/4 in Pressure control tube

1/4 in PTFE pressure 

control tube

Discharge 

valve

1/4 in compressor 

fitting and air 

bleed muffler

A 3/16 in PTFE tube (shown in green) connects the discharge valve to the fitting 

on the side of the compressor inlet valve. This provides the system air pressure 

(factory setting 140 psi) to operate the inlet valve regulator which works in tandem 

with the discharge valve (Figure 51).

Figure 51  —  3/16 in Pressure control tube

3/16 in PTFE pressure 

control tube

Discharge valve

3/16 in compressor 

fitting at inlet regulator

Summary of Contents for G300004

















































































































Reviews:

No comments