manualshive.com logo in svg

Vmac G300004, Installation, Owners And Service Manual

Share
Download
Vmac G300004 Installation, Owners And Service Manual Download Page 12

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

10

Before Starting

Read this manual as well as the Honda Owner’s Manual prior to installing or 

operating the Gas Engine Driven 30 CFM Air Compressor (G300004) to ensure 

familiarity with the components, installation requirements and how to operate the 

unit.
Open the package, unpack the components and identify them using the included 

Illustrated Parts List (IPL). 

Hose Information

The hoses used in VMAC compressor systems have a specific inner liner that is 

compatible with VMAC compressor oil. Use of hoses other than those supplied 

or recommended by VMAC may cause compressor damage and may void your 

warranty. Please contact VMAC for replacement hoses and further information.

Ordering Parts

To order parts, contact a VMAC dealer. The dealer will ask for the VMAC serial 

number, part number, description and quantity. Locate the nearest dealer online at 

www.vmacair.com/dealer-locator or call 1-877-912-6605.

General Information

Technical Support

For technical support visit VMAC’s Knowledge Base or contact the technical 

support team. 

Knowledge Base:

 http://kb.vmacair.com/   

Toll free: 

1-(888) 241- 2289

Email:

 [email protected]

Summary of Contents for G300004

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands