VKI Technologies Eccellenza Cafe Service Manual Download

Page: 70 / 108

Eccellenza Café – Service Manual

August 5, 2013

Remove the pump inlet tube from the flavoring bottle and disconnect the pump

outlet tube by pulling it off from its spout on the spout support plate.

Remove the convoluted tubing installed around the flavoring tubes. It may be

necessary to cut any tape or cable ties securing the three tubes together.

Remove the flavor pump (the flavor 2 pump is used as an example).

Loosen the two screws that secure the pump to the door.

Lift the pump until it clears the two screws, and remove it.

NOTE: When removing the flavoring tubes, have a paper towel ready as

flavoring will drip out of the ends of the tubing. It is possible that the flavoring

can stain clothing or other surfaces on which it drips.

Summary of Contents for Eccellenza Cafe













































































































Search results

Summary of Contents for Eccellenza Cafe

Reviews:

Related manuals for Eccellenza Cafe

Brands by name

Popular brands

VKI Technologies Eccellenza Cafe, Service Manual

Search results

Summary of Contents for Eccellenza Cafe

Reviews:

Related manuals for Eccellenza Cafe

Brands by name

Popular brands