VKI Technologies Eccellenza Cafe Service Manual Download Page 63

Page: 63 / 108

Eccellenza Café – Service Manual

August 5, 2013

Replacing the Bean Grinder

Switch the machine power off and unplug the service cord.

Remove the brewer assembly from the machine.

Disconnect the hot water hose from the door spout, and remove it from its

routing underneath the front of the grinder.

Remove the top cover.

Remove the left side panel.

Remove the milk and chocolate powder dispensers.

Remove the wall behind the powder dispenser area.

Loosen the two upper screws.

Remove the two lower screws and the two side screws.

CAUTION:

The bean grinder may be hot if handled immediately after

being used. If this is the case, switch the machine power OFF and

keep the door open for several minutes to allow the grinder to cool.

CAUTION: The bean grinder assembly is very heavy - use extra

caution when removing or installing the grinder.

CAUTION: Avoid touching the leads on the capacitor for the

grinder as the capacitor may hold a small electrical charge for a

few minutes after the grinder is used.

Summary of Contents for Eccellenza Cafe













































































































Search results

Summary of Contents for Eccellenza Cafe

Reviews:

Related manuals for Eccellenza Cafe

Brands by name

Popular brands

VKI Technologies Eccellenza Cafe, Service Manual

Search results

Summary of Contents for Eccellenza Cafe

Reviews:

Related manuals for Eccellenza Cafe

Brands by name

Popular brands