VKI Technologies Eccellenza Cafe Service Manual Download Page 57

Page: 57 / 108

Eccellenza Café – Service Manual

August 5, 2013

Disconnect the wiring from the valve(s) to be replaced.

Pull the valve(s) from the silicone seal support in which it is mounted. Use

caution as there may still be a bit water remaining behind the valve

when you remove it – this water may be extremely hot.

UTLET

ALVE

IRING

ONNECTIONS

Coffee Valve

Red Wires

Powder Valve

White Wires

Hot Water Valve

Yellow Wires

To re-install an outlet valve, follow these same instructions, but in the reverse

order.

NOTE: If the coffee valve is replaced, it may be necessary to adjust the valve’s

flow rate by using the restrictor at the front of the valve. To decrease the flow,

turn the restrictor clockwise. To increase the flow, turn it counter-clockwise.

Summary of Contents for Eccellenza Cafe













































































































Search results

Summary of Contents for Eccellenza Cafe

Reviews:

Related manuals for Eccellenza Cafe

Brands by name

Popular brands

VKI Technologies Eccellenza Cafe, Service Manual

Search results

Summary of Contents for Eccellenza Cafe

Reviews:

Related manuals for Eccellenza Cafe

Brands by name

Popular brands