D-302756
65
you to “
<OK> TO EXIT
” or pressing the
button at the end of the
procedure will take you to the "
LAN
" menu.
The following GSM/ GPRS messages are reported:
Message
Description
Unit is OK
GSM / GPRS is functioning correctly.
GSM comm. loss
The GSM/GPRS module does not communicate with the Panel
Pin code fail
Missing or wrong PIN code.
(Only if SIM card PIN code is enabled.)
GSM net. fail
Unit failed with registration to local GSM network.
SIM card fail
SIM not installed or SIM card failure.
GSM not detected
GSM auto enroll failed to detect GSM/GPRS module.
No GPRS service
The SIM card does not have the GPRS service enabled.
GPRS conn. fail
Local GPRS network is not available or, wrong setting to GPRS APN, user and/or password.
Srvr unavailable
IPMP Receiver cannot be reached – Check the Server IP
IP not defined
Server IP #1 and #2 are not configured.
APN not defined
APN is not configured.
SIM card locked
After entering a wrong PIN code 3 consecutive times the SIM is locked. To unlock it enter a PUK
number. The PUK number cannot be entered by the PowerMax10-G2.
Denied by server
The IPMP denies the connection request. Check that the Panel is registered to the IPMP Receiver.
5.1.6 LAN Connection Test
The LAN Connection diagnostic procedure tests Broadband Module communication to the IPMP and reports the diagnostic
result. In case of communication failure, detailed information of the failure is reported.
If the Broadband Module is not registered to the PowerMax10-G2, the menu "
LAN CONNECT.TEST
" will not be displayed.
1.
Make sure the system is disarmed and then press the
button
repeatedly until the PowerMax10-G2 display reads
"
INSTALLER MODE
".
2.
When the PowerMax10-G2 display reads
[
INSTALLER MODE
]
,
press
OK
I
.
OK
I
The screen will now prompt you to enter your installer code.
3.
Enter your Installer Code.
The PowerMax10-G2 display will read [
NEW INSTL CODE
].
CODE
4.
When the PowerMax10-G2 display reads
[
NEW INSTL CODE
]
press the
or
button repeatedly until the PowerMax10-G2 display will read
[
DIAGNOSTICS
].
or
5.
When the PowerMax10-G2 display reads [
DIAGNOSTICS
], press the
OK
I
button.
The PowerMax10-G2 display will read [
WL DEVICES
].
∗
OK
I
6.
When the PowerMax10-G2 display reads [
WL DEVICES
], press the
or
button repeatedly until the PowerMax10-G2 display will read [
LAN
].
or
7.
When the PowerMax10-G2 display reads [
LAN
], press the
OK
I
button.**
OK
I
8.
The PowerMax10-G2 display will read [
PLEASE WAIT…
] and will then
automatically change to read [
UNIT IS OK
].
See the table below for a complete list of possible LAN messages.
∗
If there are no wireless devices enrolled in the PowerMax10-G2 system, the
PowerMax10-G2 display reads [
NO DEVICES
].
** When the
OK
I
button is pressed the test result takes between 15 sec. to
4 min. before it is displayed, depending on the severity of the failure.
Pressing the
or
buttons at any stage in the procedure will take
you to “
<OK> TO EXIT
” or pressing the
button at the end of the
procedure will take you to the "
LAN RESET OPTION
" menu.
UNIT IS OK
PLEASE WAIT…
NEW INSTL CODE
ENTER CODE:
INSTALLER MODE
READY 00:00
LAN
WL DEVICES
DIAGNOSTICS
