Villa Rotograph EVO Service Manual Download Page 56

Page: 56 / 223

SERVICE MANUAL

Pre-installation

(Rev. 1)

Rotograph EVO

5-5

5.2. Packaging

Rotograph EVO in base version is delivered in two carton-board boxes;
the device equipped with Cephalometric unit will be delivered in three

boxes.

Weight

Contents

Net

Gross

- Axis movement device, complete

with tubehead

- Covers

80 kg

(176 lbs)

95 kg

(209 lbs)

- Column complete with console

- Covers

- Accessories

145 kg

(319 lbs)

160 kg

(352 lbs)

- Cephalometric device

- Covers

- Accessories for Cephalometric

device

57 kg

(126 lbs)

72 kg

(159 lbs)

NOTE:

All boxes mount shock detectors.
At the receiving and before opening boxes, verify that those sensors have

not been activated.

WARNING:

Villa Sistemi Medicali will not bear any responsibility for damages

caused to the equipment due to improper unpackaging procedure,
and for the relevant costs.

Summary of Contents for Rotograph EVO
































































































































































































































Search results

Summary of Contents for Rotograph EVO

Reviews:

Brands by name

Popular brands

Villa Rotograph EVO, Service Manual

Search results

Summary of Contents for Rotograph EVO

Reviews:

Brands by name

Popular brands