Villa Rotograph EVO Service Manual Download Page 110

Page: 110 / 223

SERVICE MANUAL

Troubleshooting

(Rev. 1)

Rotograph EVO

8-19

8.2.4.3. E752: Filament overload / E753: Overload on Anodic current

These messages are displayed when an abnormal value of filament or
anodic current have been detected.

Replace the tubehead and then the Generator board.

8.2.4.4. E754: Broken filament

This message is displayed when there is a fault on the power circuit of

the filament, not only the filament itself.

Check that connector X56 is well inserted.
Check the continuity of wires from X57 to the tubehead.
Verify the correctness of pre-heating parameters.

If all OK, replace the tubehead.

8.2.4.5. E756: PFC failure

This message is signalling that the PFC (Power Factor Control) circuit is
not correctly functioning.

If the error is present in stand-by mode, replace the Generator board

(A10).
If the error appears during an exposure, reset the error and repeat the
exposure; if the error still appears, replace the Generator board and then

the tubehead.

Summary of Contents for Rotograph EVO
































































































































































































































Search results

Summary of Contents for Rotograph EVO

Reviews:

Brands by name

Popular brands

Villa Rotograph EVO, Service Manual

Search results

Summary of Contents for Rotograph EVO

Reviews:

Brands by name

Popular brands