Victron energy BlueSolar SCC010005000 Manual Download Page 75

Page: 75 / 122

1. General Safety Information

Read all instructions and cautions in the manual before starting the
installation.

Keep the controller away from rain exposure, severe dust, vibration,
corrosive gas and intense electromagnetic interference.

Do not allow water to enter the controller.

There are no user serviceable parts inside the controller. Do not
disassemble or attempt to repair it.

2. Features

•

Lighting control function, fully programmable with software
(available free of charge on our website), or the Remote Panel.

•

Three stage battery charging (bulk, absorption, float), fully
programmable.

•

Integrated battery monitor function (Remote Panel needed to
display state of charge).

•

Load output with low voltage disconnect and manual control
(default setting).

•

Optional external temperature sensor.

•

Load output protected against over load and short circuit.

•

Protected against reverse polarity connection of the solar array
and/or battery.

Summary of Contents for BlueSolar SCC010005000



























































































































Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands

Victron energy BlueSolar SCC010005000, Manual

Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands