Victron energy BlueSolar SCC010005000 Manual Download Page 112

Page: 112 / 122

3.2. Display

After connecting the remote panel, the default monitoring display will
be shown:

Charge current icon

Battery status icons

Load status icon

Day/night.

Battery icon Load current icon

PV- V & A.

Battery-V&A

Load-V&A

Day and night icons

- Night

，

- day. If the voltage of the solar array is above 1V, the

daytime icon is shown.

Battery icon

The battery icon shows the state of charge of the battery. For this
function the correct battery capacity must be set (see section 5.4) and
all loads must connected to the load output (i.e. not directly to the
battery).

Note: When the battery is fully discharged, the icon displayed is

Summary of Contents for BlueSolar SCC010005000



























































































































Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands

Victron energy BlueSolar SCC010005000, Manual

Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands